Effect of gas temperature on carbon soot oxidation via non-thermal plasma: two-dimensional numerical study integrating reactive flow and discharge models.

Non-thermal plasma (NTP) efficiently regenerates diesel particulate filters by oxidizing carbon soot (CS) at low temperatures. However, numerical studies on the spatial characteristics of CS oxidation by NTP are scarce. In addition, the influence of background gas heating on the CS-oxidizing performance by NTP remains inadequately understood. This research investigates the impact of gas temperature (323-573 K) on heterogeneous CS oxidation using NTP in a two-dimensional configuration. The results indicate that CS is mainly oxidized by [Formula: see text], [Formula: see text], and [Formula: see text] during NTP treatment. The energy efficiency of CS removal by NTP ranges from 0.1 to 2.6 g kWh-1 for varying gas temperature and applied voltage, consistent with previous research. Higher gas temperatures enhance both CS removal rate and efficiency, whereas higher applied voltages enhance rate at the expense of efficiency. The study also assesses energy conversion efficiency from electrical power input to chemical bonding energy during CS oxidation by NTP, yielding 0.03 to 0.23% efficiency for the considered gas temperature and voltage ranges, with higher temperatures leading to better efficiency.

Enhanced enrichment of collected airborne coronavirus and influenza virus samples via a ConA-coated microfluidic chip for PCR detection.

The severe acute respiratory syndrome (SARS-CoV-2) outbreak triggered global concern and emphasized the importance of virus monitoring. During a seasonal influenza A outbreak, relatively low concentrations of 103-104 viral genome copies are available per 1 m3 of air, which makes detection and monitoring very challenging because the limit of detection of most polymerase chain reaction (PCR) devices is approximately 103 viral genome copies/mL. In response to the urgent need for the rapid detection of airborne coronaviruses and influenza viruses, an electrostatic aerosol-to-hydrosol (ATH) sampler was combined with a concanavalin A (ConA)-coated high-throughput microfluidic chip. The samples were then used for PCR detection. The results revealed that the enrichment capacity of the ATH sampler was 30,000-fold for both HCoV-229E and H1N1 influenza virus, whereas the enrichment capacities provided by the ConA-coated microfluidic chip were 8-fold and 16-fold for HCoV-229E and H1N1 virus, respectively. Thus, the total enrichment capacities of our combined ATH sampler and ConA-coated microfluidic chip were 2.4 × 105-fold and 4.8 × 105-fold for HCoV-229E and H1N1 virus, respectively. This methodology significantly improves PCR detection by providing a higher concentration of viable samples.

A portable smartphone-based colorimetric sensor that utilizes dual amplification for the on-site detection of airborne bacteria.

Over the past few years, infections caused by airborne pathogens have spread worldwide, infecting several people and becoming an increasingly severe threat to public health. Therefore, there is an urgent need for developing airborne pathogen monitoring technology for use in confined environments to enable epidemic prevention. In this study, we designed a colorimetry-based bacterial detection platform that uses a clustered regularly interspaced short palindromic repeat-associated protein 12a system to amplify signals and a urease enzyme to induce color changes. Furthermore, we have developed a smartphone application that can distinguish colors under different illumination conditions based on the HSV model and detect three types of disease-causing bacteria. Even synthetic oligomers of a few picomoles of concentration and genomic DNA of airborne bacteria smaller than several nanograms can be detected with the naked eye and using color analysis systems. Furthermore, in the air capture model system, the bacterial sample generated approximately a 2-fold signal difference compared with that in the control group. This colorimetric detection method can be widely applied for public safety because it is easy to use and does not require complex equipment.

Scalable, solvent-free transparent film-based air filter with high particulate matter 2.5 filtration efficiency.

Over the course of the COVID-19 pandemic, people have realized the importance of wearing a mask. However, conventional nanofiber-based face masks impede communication between people because of their opacity. Moreover, it remains challenging to achieve both high filtration performance and transparency through fibrous mask filters without using harmful solvents. Herein, scalable transparent film-based filters with high transparency and collection efficiency are fabricated in a facile manner by means of corona discharging and punch stamping. Both methods improve the surface potential of the film while the punch stamping procedure generates micropores in the film, which enhances the electrostatic force between the film and particulate matter (PM), thereby improving the collection efficiency of the film. Moreover, the suggested fabrication method involves no nanofibers and harmful solvents, which mitigates the generation of microplastics and potential risks for the human body. The film-based filter provides a high PM2.5 collection efficiency of 99.9 % while maintaining a transparency of 52 % at the wavelength of 550 nm. This enables people to distinguish the facial expressions of a person wearing a mask composed of the proposed film-based filter. Moreover, the results of durability experiments indicate that the developed film-based filter is anti-fouling, liquid-resistant, microplastic-free and foldability.

Size-classified monitoring of ATP bioluminescence for rapid assessment of biological distribution in airborne particulates.

The COVID-19 pandemic ignited massive research into the rapid detection of bioaerosols. In particular, nanotechnology-based detection strategies are proposed as alternatives because of issues in bioaerosol enrichment and lead time for molecular diagnostics; however, the practical implementation of such techniques is still unclear due to obstacles regarding the large research and development effort and investment for the validation. The use of adenosine triphosphate (ATP) bioluminescence (expressed as relative luminescence unit (RLU) per unit volume of air) of airborne particulate matter (PM) to determine the bacterial population as a representative of the total bioaerosols (viruses, bacteria, and fungi) has been raised frequently because of the high reponse speed, resolution, and compatibility with culture-based bioaerosol monitoring. On the other hand, additional engineering attempts are required to confer significance because of the size-classified (bioluminescence for different PM sizes) and specific (bioluminescence per unit PM mass) biological risks of air for providing proper interventions in the case of airborne transmission. In this study, disc-type impactors to cut-off aerosols larger than 1 µm, 2.5 µm, and 10 µm were designed and constructed to collect PM1, PM2.5, and PM10 on sampling swabs. This engineering enabled reliable size-classified bioluminescence signals using a commercial ATP luminometer after just 5 min of air intake. The simultaneous operations of a six-stage Andersen impactor and optical PM spectrometers were conducted to determine the correlations between the resulting RLU and colony forming unit (CFU; from the Andersen impactor) or PM mass concentration (deriving specific bioluminescence).

Aero-manufacture of nanobulges for an in-place anticoronaviral on air filters.

The interest in removing contagious viruses from indoor air using ventilation and filtration systems is increasing rapidly because people spend most of the day indoors. The development of an effective platform to regenerate the antiviral function of air filters during use and safe abrogation of used filters containing infectious viruses is a challenging task, because an on-demand safe-by-design manufacture system is essential for in-place antiviral coatings, but it has been rarely investigated. With these considerations, an electrically operable dispenser was prepared for decorating continuous ultrafine Fe-Zn, Fe-Ag, or Fe-Cu particles (<5 nm) onto SiO2 nanobeads (ca. 130 nm) to form nanobulges (i.e., nanoroughness for engaging coronavirus spikes) in the aerosol state for 3 min direct deposition on the air filter surfaces. The resulting nanobulges were exposed to human coronaviruses (HCoV; surrogates of SARS-CoV-2) to assess antiviral function. The results were compared with similar-sized individual Zn, Ag, and Cu particles. The nanobulges exhibited comparable antiviral activity to Zn, Ag, and Cu particles while retaining biosafety in both in vitro and in vivo models because of the significantly smaller metallic fractions. This suggests that the bimetallic bulge structures generate reactive oxygen species and Fenton-mediated hydroxyl radicals for inactivating HCoV.

Prediction of indoor PM2.5 concentrations and reduction strategies for cooking events through various IAQ management methods in an apartment of South Korea.

Indoor PM2.5 in apartments must be effectively managed to minimize adverse impacts on human health. Cooking is the one of the main PM2.5 sources in apartments, and indoor air quality (IAQ) management methods (natural ventilation, mechanical ventilations, range hoods, and air purifiers) are typically used to reduce PM2.5 generated during cooking. For effective control of indoor PM2.5 , prediction of PM2.5 reduction for various IAQ management methods is necessary. This study carefully predicted indoor PM2.5 concentrations in an apartment when IAQ management methods were applied separately and/or in combination during cooking. The infiltration and exfiltration were verified by comparing the experimental results of CO2 concentration with those predicted with or without mechanical ventilation. The deposition rate for PM2.5 generated by cooking was also derived by comparing the experimental PM2.5 changes with the predicted values for PM2.5 natural decay. Through this method, effective PM2.5 control ways during cooking in apartments can be proposed, such as natural ventilation with a range hood for 30 min and then the operation of an air purifier for 30 min. Additionally, if this prediction is combined with energy consumption, it will be possible to propose the most energy-efficient indoor PM2.5 control methods for various seasons and outdoor conditions.

Simultaneous measurement of OH radical, H2O concentration, and temperature in a premixed CH4/air flame using TDLAS with an improved analysis method.

The OH radical concentration was measured by applying tunable diode laser absorption spectroscopy, which is an in situ optical method. An optical absorption region (P7.5ff transition at 1502.7 nm) of the OH radical was selected in the near-infrared range to measure the OH radicals quantitatively in premixed CH4/air flames. An improved direct absorption spectroscopy (DAS) method based on wavelength division multiplexing was proposed to extract the H2O absorption signal that interfered with the OH light absorption signal, and the integral intensity of OH* chemiluminescence was compared to the measured OH radical concentration based on the improved DAS method.

Efficient Energy Saving Scenarios for Indoor PM2.5 Management in an Apartment of South Korea.

Indoor PM2.5 must be effectively controlled to minimize adverse impacts on public health. Cooking is one of the main sources of PM2.5 in residential areas, and indoor air quality (IAQ) management methods such as natural and mechanical ventilation, range hood, and air purifier are typically used to reduce cooking-generated PM2.5 concentrations. However, studies on the combined effects of various IAQ management methods on indoor PM2.5 reduction and energy consumption are limited. In this study, a theoretical model was established to estimate the performance of various IAQ management methods for controlling indoor PM2.5 concentrations and energy consumption. The model was verified by comparative experiments in which, various IAQ management methods were operated individually or combined. Seasonal energy consumption was calculated through the verified model, and energy consumption saving scenarios were derived for maintaining indoor PM2.5 concentrations less than 10 µg/m3, a World Health Organization annual guideline, under fair and poor outdoor PM2.5 concentrations of 15 and 50 µg/m3, respectively. Based on our results, we found that energy consumption could be reduced significantly by applying natural ventilation in spring, autumn, and summer and mechanical ventilation in winter. Our study identified efficient energy saving PM2.5 management scenarios using various IAQ management methods by predicting indoor PM2.5 concentration and energy consumption according to the annual life patterns of typical residents in South Korea.

Modified Aerotaxy for the Plug-in Manufacture of Cell-Penetrating Fenton Nanoagents for Reinforcing Chemodynamic Cancer Therapy.

The assemblies of anisotropic nanomaterials have attracted considerable interest in advanced tumor therapeutics because of the extended surfaces for loading of active molecules and the extraordinary responses to external stimuli for combinatorial therapies. These nanomaterials were usually constructed through templated or seed-mediated hydrothermal reactions, but the lack of uniformity in size and morphology, as well as the process complexities from multiple separation and purification steps, impede their practical use in cancer nanotherapy. Gas-phase epitaxy, also called aerotaxy (AT), has been introduced as an innovative method for the continuous assembly of anisotropic nanomaterials with a uniform distribution. This process does not require expensive crystal substrates and high vacuum conditions. Nevertheless, AT has been used limitedly to build high-aspect-ratio semiconductor nanomaterials. With these considerations, a modified AT was designed for the continuous in-flight assembly of the cell-penetrating Fenton nanoagents (Mn-Fe CaCO3 (AT) and Mn-Fe SiO2 (AT)) in a single-pass gas flow because cellular internalization activity is essential for cancer nanotherapeutics. The modified AT of Mn-Fe CaCO3 and Mn-Fe SiO2 to generate surface nanoroughness significantly enhanced the cellular internalization capability because of the preferential contact mode with the cancer cell membrane for Fenton reaction-induced apoptosis. In addition, it was even workable for doxorubicin (DOX)-resistant cancer cells after DOX loading on the nanoagents. After combining with immune-checkpoint blockers (antiprogrammed death-ligand 1 antibodies), the antitumor effect was improved further with no systemic toxicity as chemo-immuno-chemodynamic combination therapeutics despite the absence of targeting ligands and external stimuli.

Numerical methodology to evaluate unipolar saturation current limit of DC corona discharge in complex geometries.

The unipolar saturation current limit ([Formula: see text]) gives an upper limit to the corona current that can be obtained from a unipolar corona discharge. Therefore, it implies a theoretical limit to the performance of unipolar corona discharge devices. However, it has not been widely used in practice because it is difficult to deal with complex discharge configurations in an analytical way. This study aims to establish and validate a numerical methodology to evaluate the maximum current, which numerically imitates the unipolar saturation current limit. It was shown that the maximum current has the same mathematical definition as the unipolar saturation current. For validation, the maximum current was compared with an analytical solution of the Poisson equation for the coaxial cylinders configuration. The differences between the maximum current and unipolar saturation current limit for the coaxial cylinders, pin-to-plane, and single wire-to-plane configurations were discussed in terms of the assumptions used in the semi-analytical derivation of the unipolar saturation current limit. The validated methodology was applied to a multiple wire-to-plane configuration, for which a semi-analytical expression of the unipolar saturation current limit has not yet been developed. The effects of geometric and operation parameters on the maximum currents of the multiple wire-to-plane configuration were analyzed. The results were regressed into a single formula.

Effects of nanosized water droplet generation on number concentration measurement of virus aerosols when using an airblast atomizer.

Development of efficient virus aerosol monitoring and removal devices requires aerosolization of the test virus using atomizers. The number concentration and size measurements of aerosolized virus particles are required to evaluate the performance of the devices. Although diffusion dryers can remove water droplets generated using atomizers, they often fail to remove them entirely from the air stream. Consequently, particle measurement devices, such as scanning mobility particle sizer (SMPS), can falsely identify the remaining nanosized water droplets as virus aerosol particles. This in turn affects the accuracy of the evaluation of devices for sampling or removing virus aerosol particles. In this study, a plaque-forming assay combined with SMPS measurement was used to evaluate sufficient drying conditions. We proposed an empirical equation to determine the total number concentration of aerosolized particles measured using the SMPS as a function of the carrier air flow rate and residence time of the particles in the diffusion dryers. The difference in the total number concentration of particles under sufficient and insufficient diffusion drying conditions was presented as a percentage of error.

Hierarchical ZnO nano-spines grown on a carbon fiber seed layer for efficient VOC removal and airborne virus and bacteria inactivation.

Air purification through fiber-based filters has become a fundamental requirement for air contamination control. However, conventional filters depend on polymeric fibrous filters with adequate particulate matter removal ability but fewer degassing and biocidal effects. This study presents the photocatalytic volatile organic compound (VOC) oxidation and antimicrobial properties of zinc oxide (ZnO) nano-spines sprouted activated-carbon nanofibers (I@ZnO/ACNFs) and their potential for air contamination control and infection prevention. By developing a novel technique that can induce phase separation of inorganic salts during electrospinning, nanofibers with zinc (Zn) components concentrated on the surface could be synthesized. I@ZnO/ACNFs exhibit a surface densely covered with high aspect-ratio ZnO nano-spines with significant lethality to airborne pathogens and enhanced photocatalytic activity toward VOCs. Moreover, excellent adhesion stability of ZnO to ACNFs under rapid airflow was observed in I@ZnO/ACNFs. In combination with intriguing antimicrobial activity and strong VOC removal capability derived from their unique morphology, novel I@ZnO/ACNFs hold potential for airborne microbial disinfection, effective and sustainable VOC purification, and the design of photomicrobicidal and photocatalytic materials.

Reusable surface amplified nanobiosensor for the sub PFU/mL level detection of airborne virus.

We developed a reusable surface-amplified nanobiosensor for monitoring airborne viruses with a sub-PFU/mL level detection limit. Here, sandwich structures consisted of magnetic particles functionalized with antibodies, target viruses, and alkaline phosphatases (ALPs) were formed, and they were magnetically concentrated on Ni patterns near an electrochemical sensor transducer. Then, the electrical signals from electrochemical markers generated by ALPs were measured with the sensor transducer, enabling highly-sensitive virus detection. The sandwich structures in the used sensor chip could be removed by applying an external magnetic field, and we could reuse the sensor transducer chip. As a proof of concepts, the repeated detection of airborne influenza virus using a single sensor chip was demonstrated with a detection limit down to a sub-PFU/mL level. Using a single reusable sensor transducer chip, the hemagglutinin (HA) of influenza A (H1N1) virus with different concentrations were measured down to 10 aM level. Importantly, our sensor chip exhibited reliable sensing signals even after more than 18 times of the repeated HA sensing measurements. Furthermore, airborne influenza viruses collected from the air could be measured down to 0.01 PFU/mL level. Interestingly, the detailed quantitative analysis of the measurement results revealed the degradation of HA proteins on the viruses after the air exposure. Considering the ultrasensitivity and reusability of our sensors, it can provide a powerful tool to help preventing epidemics by airborne pathogens in the future.

Increased survivability of coronavirus and H1N1 influenza virus under electrostatic aerosol-to-hydrosol sampling.

Airborne virus susceptibility is an underlying cause of severe respiratory diseases, raising pandemic alerts worldwide. Following the first reports of the novel severe acute respiratory syndrome coronavirus-2 in 2019 and its rapid spread worldwide and the outbreak of a new highly variable strain of influenza A virus (H1N1) in 2009, developing quick, accurate monitoring and diagnostic approaches for emerging infections is considered critical. Efficient air sampling of coronaviruses and the H1N1 virus allows swift, real-time identification, triggering early adjuvant interventions. Electrostatic precipitation is an efficient method for sampling bio-aerosols as hydrosols; however, sampling conditions critically impact this method. Corona discharge ionizes surrounding air, generating reactive oxygen species (ROS), which may impair virus structural components, leading to RNA and/or protein damage and preventing virus detection. Herein, ascorbic acid (AA) dissolved in phosphate-buffered saline (PBS) was used as the sampling solution of an electrostatic sampler to counteract virus particle impairment, increasing virus survivability throughout sampling. The findings of this study indicate that the use of PBS+AA is effective in reducing the ROS damage of viral RNA by 95%, viral protein by 45% and virus yield by 60%.

High air flow-rate electrostatic sampler for the rapid monitoring of airborne coronavirus and influenza viruses.

Capturing virus aerosols in a small volume of liquid is essential when monitoring airborne viruses. As such, aerosol-to-hydrosol enrichment is required to produce a detectable viral sample for real-time quantitative reverse transcription polymerase chain reaction (qRT-PCR) assays. To meet this requirement, the efficient and non-destructive collection of airborne virus particles is needed, while the incoming air flow rate should be sufficiently high to quickly collect a large number of virus particles. To achieve this, we introduced a high air flow-rate electrostatic sampler (HAFES) that collected virus aerosols (human coronavirus 229E, influenza A virus subtypes H1N1 and H3N2, and bacteriophage MS2) in a continuously flowing liquid. Viral collection efficiency was evaluated using aerosol particle counts, while viral recovery rates were assessed using real-time qRT-PCR and plaque assays. An air sampling period of 20 min was sufficient to produce a sample suitable for use in real-time qRT-PCR in a viral epidemic scenario.

Fabrication of silver nanowire coated fibrous air filter medium via a two-step process of electrospinning and electrospray for anti-bioaerosol treatment.

Antimicrobial agent treatment is needed to prevent airborne infections due to microorganisms causing diseases. Silver nanowires (AgNW) have been increasingly used in air filters for their superior antimicrobial performance. In this study, AgNWs (115 nm in diameter, 4-50 µm in length) were electrosprayed on the surface of polyacrylonitrile (PAN) fibres that were obtained by electrospinning. Filtration efficiency of the AgNW-coated fibres was tested by aerosolizing and convectively delivering test bacteria and virus particles to the fibres. Then the particles filtered on the fibres were cultured to evaluate antibacterial and antiviral abilities. The overall filtration efficiency of the fibres increased from 92% to 96.5% (at 2.5 cm/s of air velocity) to 98.3-99.6% after AgNW coating for 30 min (areal density = 2.352 µg per 1 cm2 of filter surface area), without affecting the pressure drop. The AgNW coating for 30 min significantly increased the antimicrobial efficiency to 98.0 ± 1.1% for Staphylococcus aureus (S. aureus), 95.2 ± 2.6% for Bacillus cereus (B. cereus), 93.7 ± 1.5% for Micrococcus luteus (M. luteus), and 72.5 ± 1.9% for bacteriophage MS2.

Collection and decomposition of oil mist via corona discharge and surface dielectric barrier discharge.

Oil mist emitted during cooking is one of the major sources of atmospheric particulate matter in urban areas. A conventional electrostatic precipitator (ESP) is used in some large restaurants; it requires regular electrode cleaning to maintain particle collection performance. However, oil mist generated during cooking is viscous and difficult to clean with water. Herein, we introduce a methodology and a device for cleaning collected oil mist using surface dielectric barrier discharge (surface-DBD) plasma. Our device uses corona discharge for the collection of oil mist. Subsequently, the oil mist collected is decomposed to gas-phase species by surface-DBD plasma. A maximum collection efficiency of 93.25% (for 230 nm di-ethyl hexyl sebacate (DEHS) particle) is obtained at a flow velocity of 1.5 m/s. The maximum oil mist decomposition efficiency is 96.4%. More than 80% of the decomposed oil mist is converted to CO2 and CO under all test conditions. Some of the byproducts other than CO and CO2 are released as particles. Higher frequency results in higher oil mist decomposition efficiency, but also higher byproduct formation of particles. The mechanism of oil mist decomposition by surface-DBD plasma is discussed using optical emission spectroscopy data.